AutoDefects
Deutsch

Citroën C3 2018: Zuverlässigkeit

Im Klassendurchschnitt

15.930 MOT-Prüfungen von Citroën C3 mit Erstzulassung 2018: 9,0% fielen wegen eines technischen Mangels durch; der Klassenmedian bei gleichem Alter und gleicher Laufleistung liegt bei 9,2%.

Technische Mängelquote
9,0%
Klassenmedian, gleiches Alter und gleiche Laufleistung
9,2%
Durchgefallen (jeder Grund)
20,2%
MOT-Prüfungen
15.930
Rückrufe
7

Was nach Laufleistung ausfällt

LaufleistungPrüfungenTechnische MängelKlassenmedian
0-50k km4.8844,8%5,2%
50-100k km9.1209,3%9,9%
100-150k km1.67617,1%15,3%
150k+ km25023,2%19,3%

Was bei diesem Baujahr ausfällt

BaugruppeTechnische Mängel
Fahrwerk und Räder1,9%
Bremsen3,1%
Motor, Abgasanlage und Emissionen2,4%
Lenkung0,3%
Karosserie, Rahmen und Rost2,7%
Gurte und Airbags0,2%
Licht und Elektrik (Verschleiß)8,2%
Reifen (Verschleiß)5,3%
Wischer und Scheibe (Verschleiß)2,7%
Sonstiges und Kennzeichen (Verschleiß)0,1%

Amtliche Rückrufe

Rückrufe der US-Behörde NHTSA und des EU Safety Gate, die dieses Modell nennen. Ob ein bestimmtes Auto betroffen ist, per FIN prüfen.

  • EU Safety Gate2015–2024

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…

    Volltext

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.

    SR/03151/25 ↗
  • EU Safety Gate2017–2023

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…

    Volltext

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.

    SR/02655/25 ↗
  • EU Safety Gate2014–2018

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…

    Volltext

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

    A12/01186/21 ↗
  • EU Safety Gate2018, 2019

    The ballast in the rear part of the vehicle could be absent.This can impair the vehicle's directional stability, increasing the risk of an accident.

    A12/00127/20 ↗
  • EU Safety GateErnst2016–2019

    A protruding weld stud may damage the bodywork wire harness and lead to a short-circuit. This may consequently cause a fire.

    A12/0584/19 ↗
  • EU Safety GateErnst2018

    The steering column may have been incorrectly fixed to the shaft of the vehicle's steering system. The steering column might consequently detach from the steering system, leading to a loss of steering control.

    A12/0238/19 ↗
1 weitere Rückrufe anzeigen
  • EU Safety GateErnst2018

    The steering column assembly may not be correct. This could lead to a loss of steering control.

    A12/1357/18 ↗