AutoDefects
Español

Citroën C3 2018: fiabilidad

18 % menos fallos mecánicos que su clase

15.930 inspecciones MOT de Citroën C3 matriculados por primera vez en 2018: el 9,0 % no pasó por un defecto mecánico; la mediana de su clase con la misma edad y kilometraje es del 11,0 %.

Tasa de fallo mecánico
9,0%
Mediana de la clase, misma edad y kilometraje
11,0%
No pasó la MOT (cualquier motivo)
20,2%
inspecciones MOT
15.930
Llamadas a revisión
7

Qué falla según el kilometraje

KilometrajeInspeccionesFallo mecánicoMediana de la clase
0-50k km48844,8%6,2%
50-100k km91209,3%12,2%
100-150k km167617,1%17,1%
150k+ km25023,2%18,3%

Qué falla en este año

SistemaFallo mecánico
Suspensión y ruedas1,9%
Frenos3,1%
Motor, escape y emisiones2,4%
Dirección0,3%
Carrocería, bastidor y corrosión2,7%
Cinturones y airbags0,2%
Luces y electricidad (desgaste)8,2%
Neumáticos (desgaste)5,3%
Escobillas y parabrisas (desgaste)2,7%
Otros y matrículas (desgaste)0,1%

Llamadas a revisión oficiales

Campañas publicadas por la NHTSA (EE. UU.) y el EU Safety Gate que citan este modelo. Comprueba por VIN si afecta a un coche concreto.

  • EU Safety Gate2015–2024

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…

    Texto completo

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.

    SR/03151/25 ↗
  • EU Safety Gate2017–2023

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…

    Texto completo

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.

    SR/02655/25 ↗
  • EU Safety Gate2014–2018

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…

    Texto completo

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

    A12/01186/21 ↗
  • EU Safety Gate2018, 2019

    The ballast in the rear part of the vehicle could be absent.This can impair the vehicle's directional stability, increasing the risk of an accident.

    A12/00127/20 ↗
  • EU Safety GateGrave2016–2019

    A protruding weld stud may damage the bodywork wire harness and lead to a short-circuit. This may consequently cause a fire.

    A12/0584/19 ↗
  • EU Safety GateGrave2018

    The steering column may have been incorrectly fixed to the shaft of the vehicle's steering system. The steering column might consequently detach from the steering system, leading to a loss of steering control.

    A12/0238/19 ↗
Mostrar 1 llamadas más
  • EU Safety GateGrave2018

    The steering column assembly may not be correct. This could lead to a loss of steering control.

    A12/1357/18 ↗