AutoDefects
English

Small SUVs

Suzuki Jimny reliability

In 24,038 UK MOT tests, 24.5% of Suzuki Jimny cars failed for a mechanical or structural defect. The median small SUV of the same age and mileage: 24.1%.

71of 100AverageIn line with the class
Best years
2019, 2020, 2021
Years with most failures
2016, 2017, 2018
Weak spot at high mileage
Body, chassis and corrosion, Brakes, Engine, exhaust and emissions
Official recalls
6 recalls, 1 serious
Mechanical failure rate
24.5%
Class median, same age and mileage
24.1%
First MOT (3 years old), 2021
1.0% (2.0%)
MOT tests
24,038
US owner complaints
0

MOT results by test year

The whole fleet of this model at each year’s MOT, against its class at the same age and mileage. Shows whether the model keeps its standing as it ages.

MOT yearTestsMechanical failClass medianAny fail
202424,03824.5%24.1%30.8%
202324,89623.7%23.7%30.2%

Failure rate by year of first registration

Mechanical failure rate at the 2024 MOT, by the year the car was first registered, against the median of its class at the same age and mileage.

This modelClass median
0%13%26%2004: 33.5%2004 Class median: 32.1%042005: 34.1%2005 Class median: 30.6%052006: 34.4%2006 Class median: 35.5%062007: 31.6%2007 Class median: 33.2%072008: 27.2%2008 Class median: 29.5%082009: 22.7%2009 Class median: 28.9%092010: 27.0%2010 Class median: 27.7%102011: 25.2%2011 Class median: 25.5%112012: 20.7%2012 Class median: 22.2%122013: 18.1%2013 Class median: 21.7%132014: 16.2%2014 Class median: 16.0%142015: 19.7%2015 Class median: 13.0%152016: 14.7%2016 Class median: 9.5%162017: 14.0%2017 Class median: 7.4%172018: 12.7%2018 Class median: 4.7%182019: 2.3%2019 Class median: 4.1%192020: 2.0%2020 Class median: 2.7%202021: 1.0%2021 Class median: 2.0%21
YearTestsMechanical failClass medianAny failRecalls
20213991.0%2.0%6.0%0
20208842.0%2.7%8.4%1
20191,1922.3%4.1%7.1%1
201849612.7%4.7%19.8%2
201795814.0%7.4%18.7%0
20161,04014.7%9.5%19.6%0
201597719.7%13.0%25.8%0
201485916.2%16.0%22.0%2
201391018.1%21.7%23.6%2
201291420.7%22.2%27.2%1
201177725.2%25.5%32.1%0
201067527.0%27.7%32.0%0
200983922.7%28.9%29.1%0
20081,16927.2%29.5%33.8%0
20071,64931.6%33.2%37.4%0
20061,56234.4%35.5%41.5%0
20051,72234.1%30.6%40.4%0
20042,04133.5%32.1%40.6%0
Older years (6)
YearTestsMechanical failClass medianAny failRecalls
20031,71631.9%32.3%38.9%0
20021,33632.1%32.6%39.4%0
200186631.5%31.2%38.7%0
200066232.3%33.2%40.3%0
199930936.3%36.3%42.1%0
19986633.3%37.1%37.9%0

Most common MOT failures

The defects testers recorded most often on this model, in DVSA’s own wording (English), per 1,000 MOT tests.

Defect (DVSA wording)SystemPer 1,000 tests
Chassis condition: or chassis has excessive corrosion, seriously affecting its strength within 30cm of a body mountingBody, chassis and corrosion103.4
Component mounting prescribed areas: prescribed area excessively corroded significantly reducing structural strengthSuspension and wheels47.2
Prescribed areas: prescribed area strength or continuity significantly reducedSeat belts and airbags46.6
Wipers: does not clear the windscreen effectivelyWipers and windscreen (wear)46.1
Position lamp: not workingLights and electrics (wear)45.6
Rigid brake pipes: excessively corrodedBrakes44.1
Integral vehicle structure condition: corroded to the extent that the rigidity of the assembly is significantly reducedBody, chassis and corrosion41.3
Coil spring: fractured or brokenSuspension and wheels34.4
Service brake imbalance: across an axleBrakes29.7
Catalyst emissions: Lambda reading after 2nd fast idle outside specified limitsEngine, exhaust and emissions24.7
Exhaust system: has a major leak of exhaust gasesBody, chassis and corrosion23.9
Headlamp aim: projected beam image is obviously incorrectLights and electrics (wear)21.8
Service brake performance: efficiency below requirementsBrakes19.8
Swivel pins and bushes: swivel pin and/or bush excessively wornSuspension and wheels18.6
Malfunction indicator lamp: inoperative or indicates a malfunctionEngine, exhaust and emissions17.6

What fails, by mileage

Share of MOT tests that failed on each system. Wear items (bulbs, tyres, wipers, plates) are excluded from the reliability score.

System0-50k km50-100k km100-150k km150k+ km
Mechanical fail7.7% (5.2)20.0% (19.6)31.4% (30.7)35.8% (36.8)
Tests4,7636,6987,0135,564
Suspension and wheels4.9% (0.5)9.3% (1.8)12.6% (5.0)15.1% (12.4)
Brakes2.3% (1.5)8.2% (4.5)14.2% (6.2)16.2% (9.0)
Engine, exhaust and emissions0.5% (0.4)3.5% (0.7)8.4% (2.1)11.7% (4.5)
Steering0.1% (0.1)0.9% (0.3)1.9% (0.8)2.3% (1.8)
Body, chassis and corrosion0.7% (0.1)5.1% (0.4)12.6% (1.7)15.9% (4.3)
Seat belts and airbags0.2% (0.2)1.7% (0.3)4.2% (0.6)5.7% (0.9)
Lights and electrics (wear)2.5% (1.9)5.5% (3.7)12.9% (8.8)16.9% (14.8)
Tyres (wear)0.8% (3.1)1.7% (5.0)2.0% (6.7)2.9% (7.7)
Wipers and windscreen (wear)3.0% (2.6)4.9% (3.2)5.7% (3.9)6.7% (5.2)
Other and plates (wear)0.2% (0.1)0.3% (0.1)0.7% (0.2)0.8% (0.4)

(…) = Class median, same age and mileage

Pre-purchase checklist for the mechanic

Built from the systems where this model fails more often than its class at 100,000 km and above, and from open recalls.

  1. Body and chassis: inspect sills, subframes, jacking points and the floor for corrosion and previous repairs.
  2. Brakes: measure discs and pads, check brake pipes and hoses for corrosion, and test the handbrake and ABS warning light.
  3. Engine and exhaust: check for oil and coolant leaks, exhaust leaks and corrosion, warning lights, and (diesel) DPF/EGR faults and smoke.
  4. Recalls: 1 serious recall name this model — ask for proof the work was done
    • A12/00955/21 · 2020 · Due to improper design, the lead wires in the driver and passenger side door harness could be damaged or cut by the repeated motion of…

    Check a specific car by its VIN on the official sites: NHTSA (US) · DVSA (UK)

Official recalls

Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.

  • EU Safety Gate2018, 2019

    The resinous material of the fuel pump is not dense enough, can deform and come into contact with the pump housing. This can cause the pump to fail, potentially resulting in the engine stalling and increasing the risk…

    Full text

    The resinous material of the fuel pump is not dense enough, can deform and come into contact with the pump housing. This can cause the pump to fail, potentially resulting in the engine stalling and increasing the risk of accidents and injuries.

    A12/00885/24 ↗
  • EU Safety GateSerious2020

    Due to improper design, the lead wires in the driver and passenger side door harness could be damaged or cut by the repeated motion of opening and closing the doors. This may cause the curtain and side airbags to not…

    Full text

    Due to improper design, the lead wires in the driver and passenger side door harness could be damaged or cut by the repeated motion of opening and closing the doors. This may cause the curtain and side airbags to not deploy correctly in the event of an accident, increasing the risk of injury.

    A12/00955/21 ↗
  • EU Safety Gate2018

    The fuel feeding impeller in the fuel pump, which is made of resin material, may be swollen and deformed due to the insufficient material density caused by the improper injection molding process. Consequently, the…

    Full text

    The fuel feeding impeller in the fuel pump, which is made of resin material, may be swollen and deformed due to the insufficient material density caused by the improper injection molding process. Consequently, the impeller may interfere with the fuel pump housing, resulting in the fuel pump malfunction. As a result, the engine could stop while driving, increasing the risk of an accident.

    A12/00956/21 ↗
  • EU Safety Gate2013, 2014

    null The brake booster does not work adequately and thus the brake pedal operation can be harder, consequently the stopping distance can be longer.

    A12/1134/16 ↗
  • EU Safety Gate

    null Resin fragments inside the brake hydraulic control unit might get stuck in the hydraulic control valve which could lead to the anti-lock braking system (ABS) not working properly.

    A12/1047/15 ↗
  • EU Safety Gate2012–2014

    null The fastening bolts of the joint between the lateral rod and the axle housing in the front and rear suspension systems may become loose. In the worst case, the bolts can drop off. If this happens, and if the car is…

    Full text

    null The fastening bolts of the joint between the lateral rod and the axle housing in the front and rear suspension systems may become loose. In the worst case, the bolts can drop off. If this happens, and if the car is used in this condition, the operation of the steering might be affected.

    A12/0834/14 ↗