AutoDefects
English

Small SUVs

Suzuki SX4 / S-Cross reliability

In 41,661 UK MOT tests, 19.0% of Suzuki SX4 / S-Cross cars failed for a mechanical or structural defect. The median small SUV of the same age and mileage: 20.4%.

77of 100Average7% fewer mechanical failures than the class
Best years
2015, 2020, 2021
Years with most failures
2010, 2011, 2012
Weak spot at high mileage
Suspension and wheels, Brakes, Engine, exhaust and emissions
Official recalls
7 recalls, 1 serious
Mechanical failure rate
19.0%
Class median, same age and mileage
20.4%
First MOT (3 years old), 2021
1.4% (2.5%)
MOT tests
41,661
US owner complaints
0

MOT results by test year

The whole fleet of this model at each year’s MOT, against its class at the same age and mileage. Shows whether the model keeps its standing as it ages.

MOT yearTestsMechanical failClass medianAny fail
202441,66119.0%20.4%28.8%
202341,37119.7%19.6%29.1%

Failure rate by year of first registration

Mechanical failure rate at the 2024 MOT, by the year the car was first registered, against the median of its class at the same age and mileage.

This modelClass median
0%15%29%2006: 39.7%2006 Class median: 37.7%062007: 38.9%2007 Class median: 36.6%072008: 34.8%2008 Class median: 32.3%082009: 35.1%2009 Class median: 32.9%092010: 35.2%2010 Class median: 31.1%102011: 33.9%2011 Class median: 30.3%112012: 32.4%2012 Class median: 25.3%122013: 25.4%2013 Class median: 26.1%132014: 15.8%2014 Class median: 21.6%142015: 9.8%2015 Class median: 17.8%152016: 8.1%2016 Class median: 13.2%162017: 7.1%2017 Class median: 10.3%172018: 4.3%2018 Class median: 6.3%182019: 3.5%2019 Class median: 4.6%192020: 1.1%2020 Class median: 3.1%202021: 1.4%2021 Class median: 2.5%212022: 1.5%2022 Class median: 2.1%22
YearTestsMechanical failClass medianAny failRecalls
2022651.5%2.1%1.5%2
20211,7621.4%2.5%9.4%2
20209061.1%3.1%8.1%2
20192,0283.5%4.6%11.2%2
20182,7244.3%6.3%13.9%1
20173,2657.1%10.3%16.3%1
20163,3998.1%13.2%18.8%3
20153,7699.8%17.8%21.2%4
20146,45315.8%21.6%26.1%1
20133,33725.4%26.1%35.2%1
20121,97232.4%25.3%41.8%0
20112,26733.9%30.3%43.1%0
20102,06335.2%31.1%44.9%0
20091,94835.1%32.9%46.2%0
20082,46434.8%32.3%45.0%0
20072,32338.9%36.6%49.3%0
200690539.7%37.7%49.4%0

Most common MOT failures

The defects testers recorded most often on this model, in DVSA’s own wording (English), per 1,000 MOT tests.

Defect (DVSA wording)SystemPer 1,000 tests
tread depth below requirements of 1.6mmTyres (wear)55.5
Rigid brake pipes: excessively corrodedBrakes50.5
Coil spring: fractured or brokenSuspension and wheels47.1
ball joint excessively wornSuspension and wheels40.2
Wipers: does not clear the windscreen effectivelyWipers and windscreen (wear)39.8
Position lamp: not workingLights and electrics (wear)34.3
Stop lamp: not workingLights and electrics (wear)29.8
Brake pads: less than 1.5 mm thickBrakes24.2
Rbt (sp): efficiency below requirementsBrakes19.5
Service brake performance: excessively bindingBrakes19.4
Pins and bushes: pin or bush excessively wornSuspension and wheels18
Condition: has ply or cords exposedTyres (wear)15.4
Headlamp aim: too highLights and electrics (wear)14.4
Malfunction indicator lamp: inoperative or indicates a malfunctionEngine, exhaust and emissions14.4
Linkage ball joints: ball joint excessively wornSuspension and wheels13.9

What fails, by mileage

Share of MOT tests that failed on each system. Wear items (bulbs, tyres, wipers, plates) are excluded from the reliability score.

System0-50k km50-100k km100-150k km150k+ km
Mechanical fail3.5% (4.1)11.9% (14.3)23.6% (25.3)35.2% (35.5)
Tests6,39314,13912,3488,781
Suspension and wheels1.7% (0.5)6.1% (1.8)13.7% (5.0)22.5% (12.4)
Brakes1.6% (1.5)6.2% (4.5)11.4% (6.2)16.4% (9.0)
Engine, exhaust and emissions0.2% (0.4)0.8% (0.7)2.4% (2.1)8.0% (4.5)
Steering0.1% (0.1)0.2% (0.3)0.6% (0.8)1.4% (1.8)
Body, chassis and corrosion0.2% (0.1)0.9% (0.4)2.7% (1.7)5.7% (4.3)
Seat belts and airbags0.1% (0.2)0.3% (0.3)0.8% (0.6)1.1% (0.9)
Lights and electrics (wear)2.8% (1.9)4.7% (3.7)10.5% (8.8)20.0% (14.8)
Tyres (wear)2.4% (3.1)5.2% (5.0)7.5% (6.7)9.5% (7.7)
Wipers and windscreen (wear)3.1% (2.6)3.9% (3.2)5.3% (3.9)6.5% (5.2)
Other and plates (wear)0.1% (0.1)0.1% (0.1)0.3% (0.2)0.5% (0.4)

(…) = Class median, same age and mileage

Pre-purchase checklist for the mechanic

Built from the systems where this model fails more often than its class at 100,000 km and above, and from open recalls.

  1. Suspension and wheels: check arms, bushes, ball joints, springs and shock absorbers for play, cracks and leaks; look for uneven tyre wear.
  2. Brakes: measure discs and pads, check brake pipes and hoses for corrosion, and test the handbrake and ABS warning light.
  3. Engine and exhaust: check for oil and coolant leaks, exhaust leaks and corrosion, warning lights, and (diesel) DPF/EGR faults and smoke.
  4. Recalls: 1 serious recall name this model — ask for proof the work was done
    • A12/0724/16 · 2013–2016 · null The seams of the front, seat-back covers may have been sewn incorrectly in the area of the side airbag. As a consequence, the seams…

    Check a specific car by its VIN on the official sites: NHTSA (US) · DVSA (UK)

Official recalls

Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.

  • EU Safety Gate2019–2024

    Due to a defective Evaporative Emission Control System (EVAP) cannister, fuel vapor can escape from the vehicle and contaminate the environment.

    A12/02341/24 ↗
  • EU Safety Gate

    The left rear brake pipe may have been damaged during tightening process, which may lead to rust development and to the creation of a hole. This may cause brake fluid leaks, resulting in impaired braking performance and…

    Full text

    The left rear brake pipe may have been damaged during tightening process, which may lead to rust development and to the creation of a hole. This may cause brake fluid leaks, resulting in impaired braking performance and loss of driving stability, increasing the risk of an accident.

    A12/00405/24 ↗
  • EU Safety Gate2015–2022

    Due to the swelling of the valve in the vacuum pump, the negative pressure of the brake boosters can be temporarily blocked. Consequently, even if the braking system remains functional, the brake pedal must be pressed…

    Full text

    Due to the swelling of the valve in the vacuum pump, the negative pressure of the brake boosters can be temporarily blocked. Consequently, even if the braking system remains functional, the brake pedal must be pressed hard, increasing the risk of an accident.

    A12/01781/22 ↗
  • EU Safety Gate

    Irregularities were found in the emission behaviour of vehicles from Suzuki. Producing disproportionate NOX emissions will harm the environment and health of human beings. The product doesn't comply with the…

    Full text

    Irregularities were found in the emission behaviour of vehicles from Suzuki. Producing disproportionate NOX emissions will harm the environment and health of human beings. The product doesn't comply with the requirements laid down in the Regulation on the approval and market surveillance of Motor Vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

    A12/01508/21 ↗
  • EU Safety Gate2015, 2016

    null The ambient temperature sensor may malfunction. If this occurs, the engine controller will not detect sensor failure and consequently the MIL (Malfunction Indicator Light) will not illuminate. These systems monitor…

    Full text

    null The ambient temperature sensor may malfunction. If this occurs, the engine controller will not detect sensor failure and consequently the MIL (Malfunction Indicator Light) will not illuminate. These systems monitor the vehicle’s exhaust and pollution control devices to ensure that they are operating properly.

    A12/0218/17 ↗
  • EU Safety GateSerious2013–2016

    null The seams of the front, seat-back covers may have been sewn incorrectly in the area of the side airbag. As a consequence, the seams are too close together and sewn too tightly so that, in the event of an accident,…

    Full text

    null The seams of the front, seat-back covers may have been sewn incorrectly in the area of the side airbag. As a consequence, the seams are too close together and sewn too tightly so that, in the event of an accident, it is possible that the side airbag will not be deployed correctly.

    A12/0724/16 ↗
Show 1 more recalls
  • EU Safety Gate2015

    null The abrasion coefficient modification coating may not been have been applied on the rear axle bolts during the manufacturing of the bolts. The bolts might consequently loosen, come off or break. If this happens,…

    Full text

    null The abrasion coefficient modification coating may not been have been applied on the rear axle bolts during the manufacturing of the bolts. The bolts might consequently loosen, come off or break. If this happens, the vehicle could become impossible to drive.

    A12/0399/16 ↗