Small SUVs
Peugeot 2008 reliability
In 132,119 UK MOT tests, 15.6% of Peugeot 2008 cars failed for a mechanical or structural defect. The median small SUV of the same age and mileage: 11.9%.
- Best years
- —
- Years with most failures
- 2018, 2019, 2021
- Weak spot at high mileage
- Body, chassis and corrosion, Suspension and wheels, Engine, exhaust and emissions
- Official recalls
- 11 recalls, 4 serious
- Mechanical failure rate
- 15.6%
- Class median, same age and mileage
- 11.9%
- MOT tests
- 132,119
- US owner complaints
- 0
Failure rate by year of first registration
Mechanical failure rate at the 2024 MOT, by the year the car was first registered, against the median of its class at the same age and mileage.
What fails, by mileage
Share of MOT tests that failed on each system. Wear items (bulbs, tyres, wipers, plates) are excluded from the reliability score.
(…) = Class median, same age and mileage
Pre-purchase checklist for the mechanic
Built from the systems where this model fails more often than its class at 100,000 km and above, and from open recalls.
- Body and chassis: inspect sills, subframes, jacking points and the floor for corrosion and previous repairs.
- Suspension and wheels: check arms, bushes, ball joints, springs and shock absorbers for play, cracks and leaks; look for uneven tyre wear.
- Engine and exhaust: check for oil and coolant leaks, exhaust leaks and corrosion, warning lights, and (diesel) DPF/EGR faults and smoke.
- Recalls: ask for proof that open recall work for this model has been done (the dealer can check by VIN).
Official recalls
Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead…
SR/01379/26 ↗Full text
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead to continuous power supply and overheating due to a blocked relay and cause a fire.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Full text
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…
SR/03153/25 ↗Full text
The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.
The fuel tank may not be leakproof and could allow fuel to leak out. In the event of leakage, leaking fuel may be ignited on hot components or from sparks and catch fire.
SR/02876/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Full text
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
Show 5 more recalls
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Full text
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Full text
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory…
SR/00434/25 ↗Full text
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to…
A12/03179/24 ↗Full text
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to stop functioning, leading to a reduction in braking efficiency. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗