Peugeot 2008 2018: reliability
16,025 MOT tests of Peugeot 2008 cars first registered in 2018: 11.3% failed for a mechanical defect; the class median at the same age and mileage is 6.5%.
- Mechanical failure rate
- 11.3%
- Class median, same age and mileage
- 6.5%
- Failed MOT (any reason)
- 22.9%
- MOT tests
- 16,025
- Recalls
- 14
What fails, by mileage
| Mileage | Tests | Mechanical fail | Class median |
|---|---|---|---|
| 0-50k km | 4,857 | 6.7% | 2.9% |
| 50-100k km | 9,387 | 12.5% | 6.9% |
| 100-150k km | 1,642 | 17.2% | 13.2% |
| 150k+ km | 139 | 25.2% | 17.8% |
What fails on this year
Official recalls
Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead…
SR/01379/26 ↗Full text
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead to continuous power supply and overheating due to a blocked relay and cause a fire.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Full text
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Full text
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Full text
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Full text
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
Show 8 more recalls
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory…
SR/00434/25 ↗Full text
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to…
A12/03179/24 ↗Full text
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to stop functioning, leading to a reduction in braking efficiency. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01870/23 ↗Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to…
A12/00046/22 ↗Full text
Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…
A12/01184/21 ↗Full text
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The rear-axle fixing screws may be defective and could break.This may result in loss of the rear axle while driving, increasing the risk of an accident.
A12/00016/19 ↗Wrong engine calibration tuning might cause the exhaust emissions' level of nitrogen oxides (NOx) to exceed regulated limits. Nitrogen oxides are harmful to human health and the environment.
A12/1594/19 ↗