Citroën C3 2021: reliability
8,433 MOT tests of Citroën C3 cars first registered in 2021: 3.6% failed for a mechanical defect; the class median at the same age and mileage is 2.8%.
- Mechanical failure rate
- 3.6%
- Class median, same age and mileage
- 2.8%
- Failed MOT (any reason)
- 9.2%
- MOT tests
- 8,433
- Recalls
- 7
What fails, by mileage
| Mileage | Tests | Mechanical fail | Class median |
|---|---|---|---|
| 0-50k km | 6,623 | 2.6% | 1.9% |
| 50-100k km | 1,671 | 6.7% | 5.9% |
| 100-150k km | 122 | 12.3% | 8.0% |
| 150k+ km | 17 | 23.5% | 9.6% |
What fails on this year
Official recalls
Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.
The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…
SR/03151/25 ↗Full text
The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02655/25 ↗Full text
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01876/23 ↗Improperly tightened rear axle components can result in loss or damage to the affected part (rod for the wheel and the chassis, brake caliper, rear axle fixing, ABS sensor, brake housing, brake housing support). This…
A11/00056/22 ↗Full text
Improperly tightened rear axle components can result in loss or damage to the affected part (rod for the wheel and the chassis, brake caliper, rear axle fixing, ABS sensor, brake housing, brake housing support). This can lead to a loss of driving stability, increasing the risk of an accident.
Incorrect tightening torques of some fastenings on the rear axle can lead to a loosening of connections. This may lead to the deterioration in braking performance, loss of control over the vehicle and even to a loss of…
A12/00511/22 ↗Full text
Incorrect tightening torques of some fastenings on the rear axle can lead to a loosening of connections. This may lead to the deterioration in braking performance, loss of control over the vehicle and even to a loss of a wheel, thereby endangering the surrounding traffic.
The outer pinion of the right driveshaft may break due to lack of heat treatment during the manufacture of the part which may lead to a break in the transmission shaft. The engine will still run, but there is no torque…
A12/00028/22 ↗Full text
The outer pinion of the right driveshaft may break due to lack of heat treatment during the manufacture of the part which may lead to a break in the transmission shaft. The engine will still run, but there is no torque transmission to the drive wheels increasing the risk of an accident.
Show 1 more recalls
The fixing screws for the ball joints may be missing.This could lead to a loss of control over the vehicle during driving, increasing the risk of an accident.
A12/00957/21 ↗