Citroën C4 2014: niezawodność
20 535 badań MOT egzemplarzy Citroën C4 zarejestrowanych po raz pierwszy w 2014: 31,0% nie przeszło z powodu usterki mechanicznej; mediana klasy w tym samym wieku i z tym samym przebiegiem to 19,1%.
- Usterki mechaniczne
- 31,0%
- Mediana klasy, ten sam wiek i przebieg
- 19,1%
- Negatywne badanie (dowolny powód)
- 42,1%
- badań MOT
- 20 535
- Akcje przywoławcze
- 19
Co się psuje w zależności od przebiegu
| Przebieg | Badania | Usterki mechaniczne | Mediana klasy |
|---|---|---|---|
| 0-50k km | 412 | 13,8% | 7,5% |
| 50-100k km | 4198 | 23,9% | 14,0% |
| 100-150k km | 8897 | 31,3% | 18,9% |
| 150k+ km | 7028 | 35,8% | 23,0% |
Co się psuje w tym roczniku
Oficjalne akcje przywoławcze
Akcje opublikowane przez NHTSA (USA) i EU Safety Gate, w których wymieniono ten model. Czy dotyczą konkretnego auta, sprawdź po VIN.
The airbag may deteriorate over time and if deployed, excessive internal pressure may cause the inflator body to burst and metal fragments could pass through the cushion material causing injury to occupants.
SR/02977/25 ↗The propellant airbag inflator may experience a material alteration over time due to degradation occurring after prolonged exposure to high absolute humidity, high temperatures and high-temperature cycling. In the event…
A12/01043/21 ↗Pełny tekst
The propellant airbag inflator may experience a material alteration over time due to degradation occurring after prolonged exposure to high absolute humidity, high temperatures and high-temperature cycling. In the event of an airbag being deployed, the excessive internal pressure may cause the inflator body to rupture and metal fragments may pass through the cushion material causing injury to the occupants.
The propellant airbag inflator may experience a material alteration over time due to degradation occurring after prolonged exposure to high absolute humidity, high temperatures and high-temperature cycling. In the event…
A12/01369/21 ↗Pełny tekst
The propellant airbag inflator may experience a material alteration over time due to degradation occurring after prolonged exposure to high absolute humidity, high temperatures and high-temperature cycling. In the event of an airbag being deployed, the excessive internal pressure may cause the inflator body to rupture and metal fragments may pass through the cushion material causing injury to the occupants. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…
A12/01186/21 ↗Pełny tekst
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The vacuum pump may be damaged by certain materials resulting from chemical corrosion of the timing belt associated with degraded oil.That can lead to reduction or loss of braking assistance, increasing the risk of an…
A12/01042/21 ↗Pełny tekst
The vacuum pump may be damaged by certain materials resulting from chemical corrosion of the timing belt associated with degraded oil.That can lead to reduction or loss of braking assistance, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The programming of the ‘Stop & Start’ system is inadequate. This may cause the engine to cut out if the battery charge level is lower than the minimum load threshold required by the ‘Stop & Start’ function. This could…
A12/0645/19 ↗Pełny tekst
The programming of the ‘Stop & Start’ system is inadequate. This may cause the engine to cut out if the battery charge level is lower than the minimum load threshold required by the ‘Stop & Start’ function. This could increase the risk of an accident.
Pokaż jeszcze 13 akcji
The piston assembly in the rear brake caliper is not correct. As a consequence, the parking brake may become less effective or fail completely.
A12/1553/18 ↗The axle of the parking brake caliper has not been correctly sealed and might corrode. As a consequence, the parking brake may become less effective or fail completely.
A12/1485/18 ↗The strut for the hatchback door may be defective. As a result, the door could suddenly drop from a raised position.
A12/0847/18 ↗Overheating of the engine may occur due to a problem with the engine control software. Overheating of the engine may lead to engine failure.
A12/0492/18 ↗There could be a fault with the power relay for the engine control unit. This could lead to the engine stalling while driving.
A12/0222/18 ↗null Water can enter the vent mechanism for the front windscreen-wiper motor. This could result in the windscreen-wiper motor becoming completely blocked because of internal corrosion. Failure of the windscreen-wipers…
A12/1522/17 ↗Pełny tekst
null Water can enter the vent mechanism for the front windscreen-wiper motor. This could result in the windscreen-wiper motor becoming completely blocked because of internal corrosion. Failure of the windscreen-wipers whilst driving in rain would lead to reduced visibility for the driver.
null Due to corrosion, the dampers of the rear door could break. This could result in the rear door failing to stay in the open position, leading to injuries to the user.
A12/1523/17 ↗null The power terminal on the starter is incorrectly positioned which could result in the electric starter cable being in contact with the exhaust gas recirculation valve. This could lead to wear of the insulation of…
A12/0997/17 ↗Pełny tekst
null The power terminal on the starter is incorrectly positioned which could result in the electric starter cable being in contact with the exhaust gas recirculation valve. This could lead to wear of the insulation of the electric starter cable and the risk of a short-circuit occurring.
null The cable of the catch inside the bonnet may be insufficiently secured. As a result, the bonnet might open unexpectedly while the vehicle is in motion, which could cause an accident.
A12/0396/17 ↗null The fixing screws for the front suspension wishbones could break, which could make it difficult for the driver to control the vehicle.
A12/1646/16 ↗null The bonnet may not lock securely and could open unexpectedly whilst driving.
A12/1585/16 ↗null Due to a problem with the fuel rail of the engine, fuel could leak.
A12/1047/16 ↗null In the case of negative exterior temperatures, and after repeated activation of the fuel heater, an electric connection on the cover of the fuel heater can overheat. This can cause the cover to melt, allowing air…
A12/1484/15 ↗Pełny tekst
null In the case of negative exterior temperatures, and after repeated activation of the fuel heater, an electric connection on the cover of the fuel heater can overheat. This can cause the cover to melt, allowing air to enter the fuel system which could lead to stalling of the engine and loss of control of the car.