Citroën C3 2022: niezawodność
233 badań MOT egzemplarzy Citroën C3 zarejestrowanych po raz pierwszy w 2022: 3,4% nie przeszło z powodu usterki mechanicznej; mediana klasy w tym samym wieku i z tym samym przebiegiem to 1,8%.
- Usterki mechaniczne
- 3,4%
- Mediana klasy, ten sam wiek i przebieg
- 1,8%
- Negatywne badanie (dowolny powód)
- 7,3%
- badań MOT
- 233
- Akcje przywoławcze
- 9
Co się psuje w zależności od przebiegu
| Przebieg | Badania | Usterki mechaniczne | Mediana klasy |
|---|---|---|---|
| 0-50k km | 200 | 3,0% | 1,4% |
| 50-100k km | 30 | 6,7% | 4,4% |
| 100-150k km | 3 | 0,0% | —% |
Co się psuje w tym roczniku
Oficjalne akcje przywoławcze
Akcje opublikowane przez NHTSA (USA) i EU Safety Gate, w których wymieniono ten model. Czy dotyczą konkretnego auta, sprawdź po VIN.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02935/25 ↗The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…
SR/03151/25 ↗Pełny tekst
The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02655/25 ↗Pełny tekst
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The oil jet cooling nozzles may be damaged. Failure to cool the crankshaft and/or pistons can cause damage to them and result in the engine stalling. This can lead to a hole forming in the engine casing, causing oil…
SR/00887/25 ↗Pełny tekst
The oil jet cooling nozzles may be damaged. Failure to cool the crankshaft and/or pistons can cause damage to them and result in the engine stalling. This can lead to a hole forming in the engine casing, causing oil leaks onto the exhaust pipe. This can cause a fire to start in the engine compartment, causing the vehicle to catch fire.
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory…
SR/00435/25 ↗Pełny tekst
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01876/23 ↗
Pokaż jeszcze 3 akcji
Due to the insufficient hardness of the steel, cracks may appear in the rear axle cross member. This affects the vehicle’s handling, increasing the risk of an accident.
A12/01766/23 ↗Insufficient tightening of screws could lead to the uncoupling of a connection between a wheel and the axle arm (front and rear), a rupture of the parking brake cable and/or a door opening unexpectedly during driving,…
A12/00437/23 ↗Pełny tekst
Insufficient tightening of screws could lead to the uncoupling of a connection between a wheel and the axle arm (front and rear), a rupture of the parking brake cable and/or a door opening unexpectedly during driving, creating a risk of an accident.
Due to improper bolts of certain components (brake caliper, rear axle mount, ratchet wheel, ABS sensor, brake hose, brake hose bracket, front control arm, horizontal front control arm, anti-roll bar, power steering),…
A12/00095/23 ↗Pełny tekst
Due to improper bolts of certain components (brake caliper, rear axle mount, ratchet wheel, ABS sensor, brake hose, brake hose bracket, front control arm, horizontal front control arm, anti-roll bar, power steering), the affected parts may be lost or damaged. This could lead to various malfunctions, such as a loss of connection between the rear wheel and axle tie rod, or a rupture of the rear brake line while the vehicle is in motion, increasing the risk of an accident.