Mercedes-Benz S-Class 2019: niezawodność
2454 badań MOT egzemplarzy Mercedes-Benz S-Class zarejestrowanych po raz pierwszy w 2019: 2,9% nie przeszło z powodu usterki mechanicznej; mediana klasy w tym samym wieku i z tym samym przebiegiem to 4,6%.
- Usterki mechaniczne
- 2,9%
- Mediana klasy, ten sam wiek i przebieg
- 4,6%
- Negatywne badanie (dowolny powód)
- 8,7%
- badań MOT
- 2454
- Akcje przywoławcze
- 9
Co się psuje w zależności od przebiegu
| Przebieg | Badania | Usterki mechaniczne | Mediana klasy |
|---|---|---|---|
| 0-50k km | 460 | 1,7% | 3,2% |
| 50-100k km | 823 | 3,3% | 4,3% |
| 100-150k km | 637 | 3,5% | 5,3% |
| 150k+ km | 534 | 2,8% | 5,4% |
Co się psuje w tym roczniku
Oficjalne akcje przywoławcze
Akcje opublikowane przez NHTSA (USA) i EU Safety Gate, w których wymieniono ten model. Czy dotyczą konkretnego auta, sprawdź po VIN.
The front axle brake hoses may develop a leak, causing brake fluid to escape. This could reduce braking performance and, if the fluid spills onto the road, reduce grip for following vehicles, increasing the risk of an…
SR/03179/26 ↗Pełny tekst
The front axle brake hoses may develop a leak, causing brake fluid to escape. This could reduce braking performance and, if the fluid spills onto the road, reduce grip for following vehicles, increasing the risk of an accident.
The polycarbonate roof panel located between the windscreen and the panoramic roof may not have been bonded correctly to the vehicle during a prior repair. In such cases, the adhesive bonding could gradually deteriorate…
A12/00730/21 ↗Pełny tekst
The polycarbonate roof panel located between the windscreen and the panoramic roof may not have been bonded correctly to the vehicle during a prior repair. In such cases, the adhesive bonding could gradually deteriorate and the panel could become detached from the vehicle, posing a risk to other road users.
A trapped particle may damage the sealing between the fuel rail and fuel injector, which could cause fuel to leak into the engine compartment. Consequently, leaking fuel may come into contact with hot parts of the…
A12/00017/22 ↗Pełny tekst
A trapped particle may damage the sealing between the fuel rail and fuel injector, which could cause fuel to leak into the engine compartment. Consequently, leaking fuel may come into contact with hot parts of the engine, increasing the risk of fire.
Due to a defect in the high fuel pressure manifold the engine might be damaged. This may lead to reduced engine power and to inability to start the vehicle, increasing the risk of an accident.
A12/00968/22 ↗The vacuum-controlled coolant pump may not be tightly sealed between the coolant and vacuum circuits. This may result in the coolant leaking into the vacuum circuit leading to an electrochemical reaction, increasing the…
A12/00045/22 ↗Pełny tekst
The vacuum-controlled coolant pump may not be tightly sealed between the coolant and vacuum circuits. This may result in the coolant leaking into the vacuum circuit leading to an electrochemical reaction, increasing the risk of fire.
The middle fold-down rear headrest may not be correctly locked into the in-use position.This could impair its protective effect, increasing the risk of injury in the event of an accident.
A12/01357/21 ↗
Pokaż jeszcze 3 akcji
Due to the lack of documentation, there is no confirmation that the screw connections of the turbocharger’s oil-supply and oil-return pipes were correctly executed during the assembly process. In the event of a loose…
A12/01336/20 ↗Pełny tekst
Due to the lack of documentation, there is no confirmation that the screw connections of the turbocharger’s oil-supply and oil-return pipes were correctly executed during the assembly process. In the event of a loose screw connection, oil might leak at the oil-supply and/or oil-return pipe of the turbocharger.The leaking oil might then come into contact with hot components, increasing the risk of fire.
The elastomer material of the oil feed line for the exhaust-gas turbocharger may not comply with the specification, allowing oil to leak out.Consequently, the leaking oil could come into contact with hot components,…
A12/01046/20 ↗Pełny tekst
The elastomer material of the oil feed line for the exhaust-gas turbocharger may not comply with the specification, allowing oil to leak out.Consequently, the leaking oil could come into contact with hot components, increasing the risk of fire.
The material used in two closure plugs on the engine might not be able to withstand the maximum load under dynamic driving conditions, allowing up to 9 liters of engine oil to escape around the plugs. Consequently, the…
A12/00923/20 ↗Pełny tekst
The material used in two closure plugs on the engine might not be able to withstand the maximum load under dynamic driving conditions, allowing up to 9 liters of engine oil to escape around the plugs. Consequently, the escaped oil could leak onto the road, posing a risk to the following traffic.