AutoDefects
English

Compact SUVs

Peugeot 5008 reliability

In 35,613 UK MOT tests, 17.4% of Peugeot 5008 cars failed for a mechanical or structural defect. The median compact SUV of the same age and mileage: 12.9%.

47of 100Below average35% more mechanical failures than the class
Best years
—
Years with most failures
2017, 2020, 2021
Weak spot at high mileage
Steering, Suspension and wheels, Brakes
Official recalls
39 recalls, 11 serious
Mechanical failure rate
17.4%
Class median, same age and mileage
12.9%
First MOT (3 years old), 2021
6.5% (3.7%)
MOT tests
35,613
US owner complaints
0

MOT results by test year

The whole fleet of this model at each year’s MOT, against its class at the same age and mileage. Shows whether the model keeps its standing as it ages.

MOT yearTestsMechanical failClass medianAny fail
202435,61317.4%12.9%30.0%
202331,01617.4%13.6%31.2%

Failure rate by year of first registration

Mechanical failure rate at the 2024 MOT, by the year the car was first registered, against the median of its class at the same age and mileage.

This modelClass median
0%14%28%2010: 38.4%2010 Class median: 31.6%102011: 34.5%2011 Class median: 30.9%112012: 34.9%2012 Class median: 28.2%122013: 31.8%2013 Class median: 26.5%132014: 27.8%2014 Class median: 20.9%142015: 23.1%2015 Class median: 17.9%152016: 20.2%2016 Class median: 14.3%162017: 18.5%2017 Class median: 10.5%172018: 12.9%2018 Class median: 8.3%182019: 9.8%2019 Class median: 6.5%192020: 8.2%2020 Class median: 4.4%202021: 6.5%2021 Class median: 3.7%212022: 6.4%2022 Class median: 2.2%22
YearTestsMechanical failClass medianAny failRecalls
20222496.4%2.2%11.7%6
20215,5956.5%3.7%15.6%6
20204,8038.2%4.4%17.9%7
20195,7749.8%6.5%19.9%10
20185,08612.9%8.3%23.2%14
201775518.5%10.5%34.0%14
20161,77720.2%14.3%39.1%14
20151,74923.1%17.9%41.7%11
20141,70827.8%20.9%47.4%11
20132,27631.8%26.5%50.1%11
20121,99934.9%28.2%50.6%10
20111,78434.5%30.9%50.0%8
20102,01938.4%31.6%52.6%8

Most common MOT failures

The defects testers recorded most often on this model, in DVSA’s own wording (English), per 1,000 MOT tests.

Defect (DVSA wording)SystemPer 1,000 tests
tread depth below requirements of 1.6mmTyres (wear)52.9
Brake pads: less than 1.5 mm thickBrakes51.5
Stop lamp: not workingLights and electrics (wear)47.3
Joints: constant velocity boot split or insecure, no longer prevents the ingress of dirtBody, chassis and corrosion35.8
Position lamp: not workingLights and electrics (wear)30.5
Registration plate lamp(s): inoperative in the case of a single lamp or all lampsLights and electrics (wear)27.8
Condition: has ply or cords exposedTyres (wear)27.4
Headlamp: not working on dipped beamLights and electrics (wear)27.4
Condition: has a cut in excess of the requirements deep enough to reach the ply or cordsTyres (wear)26.1
Coil spring: fractured or brokenSuspension and wheels21.9
Washers: provides insufficient washer liquidWipers and windscreen (wear)21.2
Headlamp aim: projected beam image is obviously incorrectLights and electrics (wear)21
Wipers: does not clear the windscreen effectivelyWipers and windscreen (wear)20.9
ball joint excessively wornSuspension and wheels20.8
Track rod end: ball joint has excessive playSteering18.8

What fails, by mileage

Share of MOT tests that failed on each system. Wear items (bulbs, tyres, wipers, plates) are excluded from the reliability score.

System0-50k km50-100k km100-150k km150k+ km
Mechanical fail5.3% (2.9)12.0% (7.5)22.3% (17.1)34.7% (28.9)
Tests7,48213,6826,9797,470
Suspension and wheels0.5% (0.7)2.4% (2.3)8.5% (7.8)18.7% (15.6)
Brakes3.2% (1.6)5.8% (4.2)8.3% (6.2)12.5% (9.6)
Engine, exhaust and emissions0.4% (0.4)1.1% (0.8)2.5% (2.0)5.1% (4.3)
Steering0.0% (0.1)0.4% (0.3)2.4% (1.5)7.0% (3.7)
Body, chassis and corrosion0.9% (0.2)2.8% (0.5)5.9% (1.5)7.0% (4.4)
Seat belts and airbags0.7% (0.2)0.9% (0.3)2.1% (0.6)3.4% (1.0)
Lights and electrics (wear)2.4% (2.0)6.3% (3.2)18.3% (7.5)28.6% (15.0)
Tyres (wear)6.3% (3.2)7.4% (5.0)9.8% (6.1)11.9% (6.9)
Wipers and windscreen (wear)2.3% (2.4)3.8% (3.0)6.0% (3.7)8.8% (5.5)
Other and plates (wear)0.1% (0.1)0.2% (0.2)0.2% (0.2)0.3% (0.4)

(…) = Class median, same age and mileage

Pre-purchase checklist for the mechanic

Built from the systems where this model fails more often than its class at 100,000 km and above, and from open recalls.

  1. Steering: check for play in the rack, track rod ends and column, power-steering leaks and noise on full lock.
  2. Suspension and wheels: check arms, bushes, ball joints, springs and shock absorbers for play, cracks and leaks; look for uneven tyre wear.
  3. Brakes: measure discs and pads, check brake pipes and hoses for corrosion, and test the handbrake and ABS warning light.
  4. Recalls: 5 serious recalls name this model — ask for proof the work was done
    • SR/01379/26 · 2008–2026 · Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic…
    • SR/01314/26 · 2025 · Vehicles may be fitted with cylinder blocks which are missing a cooling nozzle. If a cooling nozzle is missing, the piston may not be…
    • SR/02936/25 · 2008–2025 · The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may…
    • SR/03373/25 · 2025 · The connection for the auxiliary heating in the 48 V battery harness terminal may not be adequate. This issue could lead to the heating not…
    • SR/01778/25 · 2023–2025 · The low-pressure fuel line may touch the screw of the ignition coil. This contact may damage the fuel line and eventually lead to a fuel…

    Check a specific car by its VIN on the official sites: NHTSA (US) · DVSA (UK)

Official recalls

Recalls published by the US NHTSA and the EU Safety Gate that name this model. Check by VIN whether a specific car is affected.

  • EU Safety Gate2025

    Some vehicles have been registered with class A+ tyres, while the tyres actually fitted are class B. Therefore, the CO₂ emissions declared in the certificate of conformity, which are related to the tyre class, are…

    Full text

    Some vehicles have been registered with class A+ tyres, while the tyres actually fitted are class B. Therefore, the CO₂ emissions declared in the certificate of conformity, which are related to the tyre class, are incorrect. The tyre class has an impact on rolling resistance and therefore affects CO₂ emissions. Class B tyres generally have a higher rolling resistance than class A+ tyres.

    OR/00115/26 ↗
  • EU Safety Gate2023–2026

    Interior door handles may deactivate when the key is in engine-running mode, which could prevent occupants from exiting the vehicle, potentially leading to injury in the event of an accident.

    SR/01735/26 ↗
  • EU Safety GateSerious2008–2026

    Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead…

    Full text

    Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead to continuous power supply and overheating due to a blocked relay and cause a fire.

    SR/01379/26 ↗
  • EU Safety GateSerious2025

    Vehicles may be fitted with cylinder blocks which are missing a cooling nozzle. If a cooling nozzle is missing, the piston may not be cooled down sufficiently, potentially causing it to weaken, warp or break. This could…

    Full text

    Vehicles may be fitted with cylinder blocks which are missing a cooling nozzle. If a cooling nozzle is missing, the piston may not be cooled down sufficiently, potentially causing it to weaken, warp or break. This could lead to sudden engine failure, causing power transmission loss. This could also trigger thermal runaway leading to fire and injuries of the passengers.

    SR/01314/26 ↗
  • EU Safety Gate2024, 2025

    The wheel nuts are not securely tightened, which could result in the wheel nut coming loose while the vehicle is in motion, or the loss of a wheel. This could result in an accident and injuries.

    SR/00476/26 ↗
  • EU Safety GateSerious2008–2025

    The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.

    SR/02936/25 ↗
Show 33 more recalls
  • EU Safety Gate2023–2025

    The fixing screws on the front left and right ball joint mount on the front lower suspension arm may break. This could cause the ball joint mount to pivot and the affected wheel to change direction and hit the mudguard,…

    Full text

    The fixing screws on the front left and right ball joint mount on the front lower suspension arm may break. This could cause the ball joint mount to pivot and the affected wheel to change direction and hit the mudguard, which may affect the steering capacity of the vehicle and cause an accident.

    SR/04357/25 ↗
  • EU Safety Gate2023–2035

    Due to incorrect coding in the Built-in Systems Interface, the Stop&Start function is inoperative, which may result in increased CO2 emissions.

    SR/03887/25 ↗
  • EU Safety GateSerious2025

    The connection for the auxiliary heating in the 48 V battery harness terminal may not be adequate. This issue could lead to the heating not functioning properly. In rare instances, there is a possibility of an electric…

    Full text

    The connection for the auxiliary heating in the 48 V battery harness terminal may not be adequate. This issue could lead to the heating not functioning properly. In rare instances, there is a possibility of an electric arc and overheating, which might increase the risk of a fire in the vehicle.

    SR/03373/25 ↗
  • EU Safety Gate1928–1957

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared.…

    Full text

    The malfunction indicator light (MIL) may fail to illuminate if the diagnostic system of the Selective Catalytic Reduction (SCR) and/or the diesel particulate filter (DPF) malfunctions after a fault code has appeared. This could cause the vehicle to operate without the required warning, and resulting in emissions above the regulatory limits.

    SR/03153/25 ↗
  • EU Safety Gate2008–2023

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…

    Full text

    Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.

    SR/02658/25 ↗
  • EU Safety GateSerious2023–2025

    The low-pressure fuel line may touch the screw of the ignition coil. This contact may damage the fuel line and eventually lead to a fuel leak, which may cause the vehicle to catch fire.

    SR/01778/25 ↗
  • EU Safety Gate2024

    The headrests may not stay in the position they have been set in, due to defective lock slots on the headrest supports. In the event of an accident, they can come loose, which can compromise their protective function,…

    Full text

    The headrests may not stay in the position they have been set in, due to defective lock slots on the headrest supports. In the event of an accident, they can come loose, which can compromise their protective function, increasing the risk of injuries.

    SR/00884/25 ↗
  • EU Safety GateSerious2023, 2024

    Due to a weakness in the crimping interface of the quick coupling connector fitted to the high-pressure fuel pump, a leak may occur in the fuel pipe within the engine compartment. This can result in the vehicle catching…

    SR/00445/25 ↗
  • EU Safety Gate2023, 2024

    The front left or right ball joint mount on the front lower suspension arm may have defective fixing screws, which could break. Two missing screws will cause the ball joint mount to pivot and the affected wheel to…

    Full text

    The front left or right ball joint mount on the front lower suspension arm may have defective fixing screws, which could break. Two missing screws will cause the ball joint mount to pivot and the affected wheel to change direction and hit the mudguard, which may affect the steering capacity of the vehicle, increasing the risk of an accident.

    SR/00050/25 ↗
  • EU Safety Gate2024

    The subframe support can corrode, leading to cracks. This can result in the loss of structural integrity and the consequent loss of control of the vehicle.

    A12/03137/24 ↗
  • EU Safety Gate2008–2022

    In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.

    A12/02824/24 ↗
  • EU Safety Gate2008–2022

    A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.

    A12/01870/23 ↗
  • EU Safety Gate2008–2019

    Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to…

    Full text

    Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.

    A12/00046/22 ↗
  • EU Safety Gate2008–2018

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…

    Full text

    The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

    A12/01184/21 ↗
  • EU Safety Gate2018

    The passenger seat may not be adequately fastened.As a result, the seatback may not provide sufficient support in the event of an accident, increasing the risk of an injury.

    A12/00822/20 ↗
  • EU Safety Gate2016–2020

    The welding of the tow bar may be faulty. As a result, the trailer coupling could break, increasing the risk of an accident.

    A12/00646/21 ↗
  • EU Safety Gate2013–2017

    The vacuum pump may be damaged due to material abrasion of the cog belt.As a result, the braking assistance could be reduced or lost, increasing the risk of an accident.

    A12/01505/20 ↗
  • EU Safety Gate2015

    The sub-frame may corrode and fracture due to defective anti-rust treatment.This can lead to loss of control over the vehicle, increasing the risk of an accident.

    A12/01193/20 ↗
  • EU Safety Gate2019

    The two bolts attaching the trailer hitch can break.Consequently, the trailer will become detached, increasing the risk of an accident.

    A12/00381/20 ↗
  • EU Safety Gate2018, 2019

    The screws of the spare wheel support may be insufficiently tightened. As a result, the spare wheel could be detached inadvertently, increasing the risk of an accident and posing a risk to the following traffic.

    A12/1895/19 ↗
  • EU Safety Gate2008–2037

    Wrong engine calibration tuning might cause the exhaust emissions' level of nitrogen oxides (NOx) to exceed regulated limits. Nitrogen oxides are harmful to human health and the environment.

    A12/1594/19 ↗
  • EU Safety GateSerious2018

    The wiring harness on the voltage retaining device (DMTR) may have been inadequately tightened, which may cause the device to break. This could result in the engine not starting and, in very rare cases, it could start a…

    A12/0661/19 ↗
  • EU Safety GateSerious2018

    The wheel fastening nuts may have been insufficiently tightened. There is a risk that the wheel may come off or crack during driving, increasing the risk of accident.

    A12/1812/18 ↗
  • EU Safety Gate2018

    The cylinder-housing oil gallery plug may not have been correctly tightened. As a consequence oil might leak which presents a skid hazard for following traffic.

    A12/1364/18 ↗
  • EU Safety Gate2012–2015

    Engine overheating may lead to an oil leak. Engine failure while driving could lead to loss of control of the vehicle resulting in a crash.

    A12/0399/18 ↗
  • EU Safety GateSerious2016, 2017

    There could be contact between a fuel hose and the aerodynamic screen located under the fuel tank. Over time, this could cause a fuel leak underneath the vehicle.

    A12/0272/18 ↗
  • EU Safety Gate2017

    null The fixing screws of the wheel hubs on the rear cross member may not be tightened correctly. As a result, they could loosen which could lead to a loss of vehicle control while driving.

    A12/1360/17 ↗
  • EU Safety Gate2016, 2017

    null The starter motor supply terminal may come into contact with an engine component. This could lead to damage to the supply terminal and to a short circuit. As a result, it may be impossible to start the vehicle.

    A12/1344/17 ↗
  • EU Safety Gate

    null The power terminal on the starter is incorrectly positioned which could result in the electric starter cable being in contact with the exhaust gas recirculation valve. This could lead to wear of the insulation of…

    Full text

    null The power terminal on the starter is incorrectly positioned which could result in the electric starter cable being in contact with the exhaust gas recirculation valve. This could lead to wear of the insulation of the electric starter cable and the risk of a short-circuit occurring.

    A12/0996/17 ↗
  • EU Safety Gate2016, 2017

    null The hinge pin of the doors and of the retaining clip for this axis might have been incorrectly positioned, which could make it difficult to open and close the doors. If the door falls during the opening, it cannot…

    Full text

    null The hinge pin of the doors and of the retaining clip for this axis might have been incorrectly positioned, which could make it difficult to open and close the doors. If the door falls during the opening, it cannot be excluded that it could hurt a passer-by or the person opening the door from the outside.

    A12/0281/17 ↗
  • EU Safety GateSerious2016

    null Oil may leak from the turbocharger on to hot engine parts which could lead to a fire breaking out, even after the engine has been switched off.

    A12/0437/16 ↗
  • EU Safety Gate2012–2014

    null In the case of negative exterior temperatures, and after repeated activation of the fuel heater, an electric connection on the cover of the fuel heater can overheat. This can cause the cover to melt, allowing air…

    Full text

    null In the case of negative exterior temperatures, and after repeated activation of the fuel heater, an electric connection on the cover of the fuel heater can overheat. This can cause the cover to melt, allowing air to enter the fuel system which could lead to stalling of the engine and loss of control of the car.

    A12/1317/15 ↗
  • EU Safety GateSerious

    null The affected vehicles may exhibit friction wear on the driver's seat wiring harness, potentially causing an electrical malfunction or localised overheating and/or causing the driver's airbag to be triggered.

    A12/1068/14 ↗