Peugeot 208 2019: niezawodność
17 052 badań MOT egzemplarzy Peugeot 208 zarejestrowanych po raz pierwszy w 2019: 7,5% nie przeszło z powodu usterki mechanicznej; mediana klasy w tym samym wieku i z tym samym przebiegiem to 5,6%.
- Usterki mechaniczne
- 7,5%
- Mediana klasy, ten sam wiek i przebieg
- 5,6%
- Negatywne badanie (dowolny powód)
- 18,7%
- badań MOT
- 17 052
- Akcje przywoławcze
- 18
Co się psuje w zależności od przebiegu
| Przebieg | Badania | Usterki mechaniczne | Mediana klasy |
|---|---|---|---|
| 0-50k km | 9527 | 4,9% | 3,6% |
| 50-100k km | 6686 | 10,3% | 7,6% |
| 100-150k km | 730 | 13,6% | 12,8% |
| 150k+ km | 109 | 20,2% | 14,3% |
Co się psuje w tym roczniku
Oficjalne akcje przywoławcze
Akcje opublikowane przez NHTSA (USA) i EU Safety Gate, w których wymieniono ten model. Czy dotyczą konkretnego auta, sprawdź po VIN.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Pełny tekst
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Pełny tekst
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Pełny tekst
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Pełny tekst
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗
Pokaż jeszcze 9 akcji
A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01870/23 ↗The open circuit detecting system on the high voltage circuit may be over-sensitive and could unnecessarily cut off the electric current. As a result, the vehicle may lose power during driving, increasing the risk of an…
A12/00570/22 ↗Pełny tekst
The open circuit detecting system on the high voltage circuit may be over-sensitive and could unnecessarily cut off the electric current. As a result, the vehicle may lose power during driving, increasing the risk of an accident. Moreover, it could be impossible to restart or move the vehicle for several minutes.
Improper rings used for rocker panel protectors can cause them to come loose and fall on the road, posing a risk to traffic.Contact may occur between the vacuum hose and the surrounding parts. This may result in loss of…
A12/00418/22 ↗Pełny tekst
Improper rings used for rocker panel protectors can cause them to come loose and fall on the road, posing a risk to traffic.Contact may occur between the vacuum hose and the surrounding parts. This may result in loss of the braking assistance, increasing the risk of an accident.The bonnet locking screws are insufficiently tightened. As a result, the bonnet could become detached while driving, increasing the risk of an accident.
Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to…
A12/00046/22 ↗Pełny tekst
Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
The high-pressure pump has not been tightened to the engine with the correct torque. As a result, fuel may leak onto the road, posing a risk to the following traffic.
A12/01462/20 ↗The wheel alignment of the front axle may be incorrect.This may result in unstable road handling of the vehicle, increasing the risk of an accident.
A12/01171/20 ↗The fixings of the rear shock absorbers are not properly tightened. Consequently, the shock absorbers could fall while the vehicle is in movement increasing the risk of accident to incoming traffic.
A12/01021/20 ↗The front wheelhouse trims may be insufficiently fastened.As a result, they may become detached in motion, posing a risk to the following traffic.
A12/00762/20 ↗The steering column may not be manufactured according to the specifications.This may result in steering failure and loss of control over the vehicle, increasing the risk of an accident.
A12/00751/20 ↗