Peugeot 208 2020: fiabilidad
13.299 inspecciones MOT de Peugeot 208 matriculados por primera vez en 2020: el 5,4 % no pasó por un defecto mecánico; la mediana de su clase con la misma edad y kilometraje es del 4,3 %.
- Tasa de fallo mecánico
- 5,4%
- Mediana de la clase, misma edad y kilometraje
- 4,3%
- No pasó la MOT (cualquier motivo)
- 18,6%
- inspecciones MOT
- 13.299
- Llamadas a revisión
- 15
Qué falla según el kilometraje
| Kilometraje | Inspecciones | Fallo mecánico | Mediana de la clase |
|---|---|---|---|
| 0-50k km | 9244 | 3,7% | 3,1% |
| 50-100k km | 3806 | 9,1% | 6,6% |
| 100-150k km | 234 | 13,3% | 9,8% |
| 150k+ km | 15 | 6,7% | 12,3% |
Qué falla en este año
Llamadas a revisión oficiales
Campañas publicadas por la NHTSA (EE. UU.) y el EU Safety Gate que citan este modelo. Comprueba por VIN si afecta a un coche concreto.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Texto completo
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Texto completo
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Texto completo
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Texto completo
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗
Mostrar 9 llamadas más
A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01870/23 ↗The vehicle may inadvertently accelerate approximately 30 km/h above the set cruise-control speed when cruise control and the ECO mode are activated. This could increase the risk of an accident.
A12/00332/23 ↗The locking nuts of the steering tie rods may not be properly tightened. This could lead to loss of control over the vehicle, creating a risk of an accident.
A12/00246/23 ↗The open circuit detecting system on the high voltage circuit may be over-sensitive and could unnecessarily cut off the electric current. As a result, the vehicle may lose power during driving, increasing the risk of an…
A12/00570/22 ↗Texto completo
The open circuit detecting system on the high voltage circuit may be over-sensitive and could unnecessarily cut off the electric current. As a result, the vehicle may lose power during driving, increasing the risk of an accident. Moreover, it could be impossible to restart or move the vehicle for several minutes.
Due to an error in the manufacturing process, a short circuit may occur in the battery located under the front bonnet.This could increase the risk of fire while the vehicle is being charged or on is in motion.
A12/00171/22 ↗The clutch pedal on the instructor side may be impinging on the wiring harness of the heating/ventilation/air conditioning (HVAC) block. As a result, the ventilation motor will speed up, leading to increased risk of…
A12/00550/21 ↗The high-pressure pump has not been tightened to the engine with the correct torque. As a result, fuel may leak onto the road, posing a risk to the following traffic.
A12/01462/20 ↗The wheel alignment of the front axle may be incorrect.This may result in unstable road handling of the vehicle, increasing the risk of an accident.
A12/01171/20 ↗Wrong engine calibration tuning might cause the exhaust emissions' level of nitrogen oxides (NOx) to exceed regulated limits. Nitrogen oxides are harmful to human health and the environment.
A12/1594/19 ↗