AutoDefects
Deutsch

SEAT / Cupra León 2020: Zuverlässigkeit

16% mehr technische Mängel als die Klasse

13.851 MOT-Prüfungen von SEAT / Cupra León mit Erstzulassung 2020: 5,3% fielen wegen eines technischen Mangels durch; der Klassenmedian bei gleichem Alter und gleicher Laufleistung liegt bei 4,5%.

Technische Mängelquote
5,3%
Klassenmedian, gleiches Alter und gleiche Laufleistung
4,5%
Durchgefallen (jeder Grund)
13,7%
MOT-Prüfungen
13.851
Rückrufe
7

Was nach Laufleistung ausfällt

LaufleistungPrüfungenTechnische MängelKlassenmedian
0-50k km6.3233,6%2,5%
50-100k km6.3876,0%5,5%
100-150k km8819,5%9,5%
150k+ km26012,3%11,5%

Was bei diesem Baujahr ausfällt

BaugruppeTechnische Mängel
Fahrwerk und Räder2,7%
Bremsen1,6%
Motor, Abgasanlage und Emissionen1,0%
Lenkung0,1%
Karosserie, Rahmen und Rost0,2%
Gurte und Airbags0,3%
Licht und Elektrik (Verschleiß)2,4%
Reifen (Verschleiß)6,0%
Wischer und Scheibe (Verschleiß)2,3%
Sonstiges und Kennzeichen (Verschleiß)0,2%

Amtliche Rückrufe

Rückrufe der US-Behörde NHTSA und des EU Safety Gate, die dieses Modell nennen. Ob ein bestimmtes Auto betroffen ist, per FIN prüfen.

  • EU Safety Gate2020–2022

    In the event of an accident, there is a risk that the load in the baggage compartment will shoot forwards to the partition grille and cause the bracket to detach from the body, increasing the risk of injury to the…

    Volltext

    In the event of an accident, there is a risk that the load in the baggage compartment will shoot forwards to the partition grille and cause the bracket to detach from the body, increasing the risk of injury to the passengers.

    A12/01327/22 ↗
  • EU Safety Gate2020–2022

    In the event of an accident, there is a risk that the load in the baggage compartment will shoot forwards to the partition grille and cause the bracket to detach from the body, increasing the risk of injury to the…

    Volltext

    In the event of an accident, there is a risk that the load in the baggage compartment will shoot forwards to the partition grille and cause the bracket to detach from the body, increasing the risk of injury to the passengers.

    A12/01328/22 ↗
  • EU Safety GateErnst2020–2022

    A faulty fuse can cause an arc flash in the event of a short circuit and cause a fire.

    A12/00676/22 ↗
  • EU Safety GateErnst2020–2022

    In the event of a short circuit, a faulty fuse can cause an arc flash, which could cause fire and lead to an accident.

    A12/00697/22 ↗
  • EU Safety GateErnst2020–2022

    The engine covers installed could detach from their fixings depending on the conditions of use (e.g. very sporty driving, or poor road surfaces) and their age. A loose engine cover could come into contact with the hot…

    Volltext

    The engine covers installed could detach from their fixings depending on the conditions of use (e.g. very sporty driving, or poor road surfaces) and their age. A loose engine cover could come into contact with the hot area of the exhaust gas turbocharger, increasing the risk of burns or fire.

    A12/00608/22 ↗
  • EU Safety Gate2020

    During the process of assembling the rear stub axle housing at the supplier’s, it is possible that the attachment screw of the rear right or rear left stub axle housing was not tightened to the required torque. Friction…

    Volltext

    During the process of assembling the rear stub axle housing at the supplier’s, it is possible that the attachment screw of the rear right or rear left stub axle housing was not tightened to the required torque. Friction noise may occur in the area of the rear axle during operation, which may be followed by loss of control of the vehicle when the stub axle housing comes loose, increasing the risk of an accident.

    A11/00108/21 ↗
1 weitere Rückrufe anzeigen
  • EU Safety GateErnst2020, 2021

    Due to a manufacturing error, seat belt anchorage points for the front seats may be inadequate.This will impair the seat belts' protective effect in the event of a collision or sudden braking, increase the risk of…

    Volltext

    Due to a manufacturing error, seat belt anchorage points for the front seats may be inadequate.This will impair the seat belts' protective effect in the event of a collision or sudden braking, increase the risk of injury. The product does not meet the requirements set out in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.

    A12/01388/21 ↗