Peugeot 2008 2021: Zuverlässigkeit
17.607 MOT-Prüfungen von Peugeot 2008 mit Erstzulassung 2021: 3,8% fielen wegen eines technischen Mangels durch; der Klassenmedian bei gleichem Alter und gleicher Laufleistung liegt bei 2,4%.
- Technische Mängelquote
- 3,8%
- Klassenmedian, gleiches Alter und gleiche Laufleistung
- 2,4%
- Durchgefallen (jeder Grund)
- 14,0%
- MOT-Prüfungen
- 17.607
- Rückrufe
- 11
Was nach Laufleistung ausfällt
| Laufleistung | Prüfungen | Technische Mängel | Klassenmedian |
|---|---|---|---|
| 0-50k km | 12.543 | 2,4% | 1,6% |
| 50-100k km | 4.775 | 6,7% | 4,4% |
| 100-150k km | 265 | 13,6% | 7,5% |
| 150k+ km | 24 | 16,7% | 1,9% |
Was bei diesem Baujahr ausfällt
Amtliche Rückrufe
Rückrufe der US-Behörde NHTSA und des EU Safety Gate, die dieses Modell nennen. Ob ein bestimmtes Auto betroffen ist, per FIN prüfen.
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead…
SR/01379/26 ↗Volltext
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead to continuous power supply and overheating due to a blocked relay and cause a fire.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Volltext
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Volltext
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Volltext
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Volltext
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
5 weitere Rückrufe anzeigen
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory…
SR/00434/25 ↗Volltext
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to…
A12/03179/24 ↗Volltext
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to stop functioning, leading to a reduction in braking efficiency. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01870/23 ↗Wrong engine calibration tuning might cause the exhaust emissions' level of nitrogen oxides (NOx) to exceed regulated limits. Nitrogen oxides are harmful to human health and the environment.
A12/1594/19 ↗