Peugeot 2008 2017: niezawodność
16 604 badań MOT egzemplarzy Peugeot 2008 zarejestrowanych po raz pierwszy w 2017: 16,4% nie przeszło z powodu usterki mechanicznej; mediana klasy w tym samym wieku i z tym samym przebiegiem to 10,7%.
- Usterki mechaniczne
- 16,4%
- Mediana klasy, ten sam wiek i przebieg
- 10,7%
- Negatywne badanie (dowolny powód)
- 27,9%
- badań MOT
- 16 604
- Akcje przywoławcze
- 15
Co się psuje w zależności od przebiegu
| Przebieg | Badania | Usterki mechaniczne | Mediana klasy |
|---|---|---|---|
| 0-50k km | 2809 | 8,2% | 4,6% |
| 50-100k km | 9645 | 16,7% | 10,1% |
| 100-150k km | 3655 | 20,9% | 15,7% |
| 150k+ km | 495 | 25,5% | 22,0% |
Co się psuje w tym roczniku
Oficjalne akcje przywoławcze
Akcje opublikowane przez NHTSA (USA) i EU Safety Gate, w których wymieniono ten model. Czy dotyczą konkretnego auta, sprawdź po VIN.
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead…
SR/01379/26 ↗Pełny tekst
Due to a defect of the engine control unit (inverter) in the vehicles fitted with electric double clutch transmission (e-DCT), metallic soldering residues may cause an internal electric short-circuits. This could lead to continuous power supply and overheating due to a blocked relay and cause a fire.
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient…
SR/00819/26 ↗Pełny tekst
The vehicle may have contact, or insufficient clearance (< 10 mm), between the petrol particulate filter pipe and the terminal protection cap of the 48 V belt starter generator. In wet conditions, the insufficient clearance and possible contact between these components can lead to water infiltration, causing an electric arc, that could trigger a thermal event, such as overheating, which may lead to fire.
The vehicle may have a fuel leak in the high-pressure hose, between the high-pressure pump and the rail, because of loose nuts. This may cause a fire in the vehicle.
SR/02936/25 ↗Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control…
SR/02658/25 ↗Pełny tekst
Due to oil carbonisation and high contact pressure, the 7 mm camshaft chain resistance can be reduced. This may cause the camshaft chain to break, leading to an engine failure. This can cause a loss of vehicle's control and increase the risk of accidents and injuries.
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the…
SR/02104/25 ↗Pełny tekst
The aluminium of the EBS valve block may not fully cast around the valves. This can lead to an internal leak of brake fluid (from one or more of the 12 valve seats) resulting in a reduction of the fluid level and the deactivation of stability control due to damage to the pressure sensor. The brake fluid could come into contact with the printed circuit board and result in the deactivation of all control functions (including the anti-lock system and electronic brake force distribution).
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started,…
SR/01450/25 ↗Pełny tekst
The software supposed to prevent the engine from stopping suddenly and to transmit data to customer service is not working properly. This can lead the ‘Ready’ mode to be unavailable after the vehicle has been started, to an acceleration power's loss and to the engine suddenly cutting out while driving. This increases the risk of accidents and injuries.
Pokaż jeszcze 9 akcji
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory…
SR/00434/25 ↗Pełny tekst
Due to a faulty software of the electronic engine control unit (ECU), an incorrect value may be given when the data are processed by the vehicle. This may result in nitrogen oxide (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to…
A12/03179/24 ↗Pełny tekst
When there is a specific error in the vacuum circuit and after 6 seconds with the brake applied, the electronic control unit send an "Invalid Value" to the hydraulic brake compensation (HBC). This can cause the HBC to stop functioning, leading to a reduction in braking efficiency. This increases the risk of accidents and injuries.
In certain vehicles fitted with the DV5R E6.3 engine, the nitrogen oxide (NOx) emissions are above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
A12/02824/24 ↗A software error in the engine control unit prevents the malfunction indicator light (MIL) from switching on if the urea injector stops working. This can lead to higher emissions and poses a risk to the environment.
A12/01870/23 ↗Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to…
A12/00046/22 ↗Pełny tekst
Computer software used in after-sales operations between October 2020 and January 2021 was incorrect. This may lead to Nitrogen Oxides (NOx) emissions above the regulatory limits. Excessive NOx emissions pose a risk to the environment.
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of…
A12/01184/21 ↗Pełny tekst
The teeth of the timing belt may wear off prematurely due to excessive dynamic tension in dusty conditions. As a result, the engine may stall at high engine speeds and not being able to restart, increasing the risk of an accident. The product does not meet the requirements laid down in the Regulation on the approval and market surveillance of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles.
The vacuum pump may be damaged due to material abrasion of the cog belt.As a result, the braking assistance could be reduced or lost, increasing the risk of an accident.
A12/01505/20 ↗The rear-axle fixing screws may be defective and could break.This may result in loss of the rear axle while driving, increasing the risk of an accident.
A12/00016/19 ↗Wrong engine calibration tuning might cause the exhaust emissions' level of nitrogen oxides (NOx) to exceed regulated limits. Nitrogen oxides are harmful to human health and the environment.
A12/1594/19 ↗